Updated November 2026

LED under kitchen cabinets gives you bright, focused task light right where you chop, mix and read recipes. This guide walks through how to plan the layout, pick the right strips and fixtures, and wire them so the light is even and free of hot spots. Most of the work is in the planning, so measure twice before you buy.

Plan the Layout Before You Buy Anything

Start by measuring the run of cabinets where the light will go, from the back edge of the cabinet to the front lip. Under-cabinet lighting works best when the fixture sits near the front of the cabinet bottom, so the light falls on the counter rather than the backsplash. For a standard 24-inch-deep base run, a light placed about 1 to 2 inches from the front edge keeps the beam on the work surface. If you are still sorting out fixture types, Best Under-Cabinet Lighting for Kitchens: 6 Fixtures Compared lays out the main options side by side.

Shopping for one? See our guide: 7 Best Kitchens Under Cabinet Organizer Picks Compared (2026).

Choose the Light Type and Spacing

LED tape, linear puck lights and bar fixtures each behave differently. Tape gives a continuous line of light and suits long, uninterrupted runs. Pucks and bars are easier to replace individually and work better when you need to avoid a visible seam. Manufacturers typically specify a maximum run length for each LED strip before voltage drop becomes a problem, so check that number and power the run from both ends if you exceed it.

For even coverage, most designers space pucks or bars about 12 to 18 inches apart. Tape should run the full length of the cabinet with a strip or diffuser over it to avoid bright dots. Color temperature matters as much as spacing. Many homeowners choose 3000K for a warm, cozy feel or 4000K for crisper task light, and a consistent color across all fixtures is worth confirming before installation.

Mount the Fixtures and Run Wiring

Mount the fixtures to the underside of the cabinet bottom, keeping the wire route hidden behind the cabinet frame or in a channel. Plan where the driver or transformer will sit, usually inside a cabinet or on the upper side of a wall, and make sure it is accessible for service. Keep low-voltage wiring separate from line-voltage wiring, and follow the manufacturer’s instructions for the power supply. If you want more background, see 5 Best Cabinet Blind Corner Organizers for Every Kitchen Setup.

Control and Power the System

Decide early whether the lights will switch on a wall switch, a plug-in dimmer, a motion sensor or a smart controller. Dimming needs a compatible driver, so confirm that before you buy. Work involving line voltage, outlets or new circuits should be done by a licensed electrician. Consult a professional for any hardwired work to protect yourself and meet local code.

Checklist for Your Install

  1. Measure the full run and mark the front-edge mounting line.
  2. Confirm fixture type, spacing and color temperature match across the run.
  3. Calculate total wattage and check the power supply rating with a margin.
  4. Plan wire routes, driver location and access for future service.
  5. Test each section before closing up cabinets or covering tape.

Common Mistakes

  • Mounting fixtures too far back, which leaves the counter front in shadow.
  • Exceeding the maximum run length on a single LED strip without feeding power from both ends.
  • Mixing color temperatures, which creates visible differences between sections.
  • Skipping a diffuser on tape lighting, which leaves bright dots on the counter.
  • Forgetting that dimmers need a compatible driver.

A reliable LED strip with a matched power supply keeps voltage stable across the run and simplifies wiring. View on Amazon

A aluminum channel with a frosted diffuser hides the strip and softens the light so you avoid hot spots. View on Amazon

A plug-in LED dimmer lets you adjust brightness without rewiring the fixtures. View on Amazon

FAQ

Can I install led under kitchen cabinets myself?

Low-voltage LED kits that plug into a wall outlet are usually a manageable DIY project. Any hardwired connection or new circuit should be handled by a licensed electrician.

How far apart should LED pucks be spaced?

A common starting point is 12 to 18 inches between fixtures. Check the manufacturer’s spacing guidance and adjust based on fixture brightness and counter depth.

Which color temperature works best for kitchen counters?

Many people prefer 3000K for a warm feel and 4000K for crisper task light. Choose one and use it across the entire run for a consistent look.

Conclusion

Good under-cabinet light comes from careful planning: fixture placement near the front edge, consistent spacing and color, and a power setup sized for the full run. Measure carefully, test before closing up, and bring in a licensed electrician for any hardwired work. For more on fitting lighting into your cabinet plan, see Lighting Underneath Kitchen Cabinets: 7 Steps to Even, Glare-Free Light.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our kitchen design & remodeling guides, checking product details against manufacturer specifications and owner feedback.