Updated November 2026

To install lighting under kitchen cabinets, you plan the fixture spacing, mount the channel or puck lights to the underside of the upper cabinets, and connect them to a power source through a switch or dimmer. Done well, the result is bright, even task light on the countertop with no hot spots and no exposed wire. The process takes a weekend for most kitchens if the wiring path is simple.

Plan the Layout Before You Buy Anything

Start by measuring the length of each run of upper cabinets, from one side to the other. Mark the center of the counter where you prepare food, since that is where you need the most light. Most installers space LED strips or pucks about 6 to 12 inches apart, depending on fixture output and how far the light sits from the counter. Check the manufacturer’s spacing rules and keep the lights a few inches in from the cabinet front so the bulbs stay out of sight.

Shopping for one? See our guide: 5 Best Kitchen Cabinet Door Hinges for Soft Close and Easy Install (2026).

If you are still weighing fixture types, Best Under-Cabinet Lighting for Kitchens: 6 Fixtures Compared covers the main options. For layout decisions, see Under-Cabinet Lighting: Planning Counter Light.

Gather Tools and Materials

  1. LED light fixtures rated for under-cabinet use, plus connectors and a power supply sized to the total load.
  2. A drill with bits, a stud finder, a level and a tape measure.
  3. Wire nuts or plug-in connectors, a voltage tester and a wire stripper.
  4. Mounting clips, adhesive pads or screws, depending on the fixture.
  5. A wall switch, a plug-in timer or a dimmer, if you want control beyond on and off.

Mount the Fixtures and Route the Wiring

Turn off power at the breaker before you touch any wiring. Mark the fixture line on the underside of the cabinets, using a level so the run stays straight. Attach mounting clips or the adhesive backing, then press each fixture into place. Route the low-voltage cable along the cabinet bottom or behind a trim piece, and keep it clear of the hinges and the face frame.

Plan where the power supply will sit. Many installers put it inside a cabinet with ventilation, away from the sink and dishwasher. Leave a service loop so you can reach the driver later if you need to replace it.

Connect Power and Control the Lights

Connect the fixtures to the power supply according to the manufacturer’s diagram, keeping polarity consistent. If the supply is hardwired, a licensed electrician should make the connection to the household circuit. Plug-in models reduce this step but still need a grounded outlet within reach. Test each section with a voltage tester before you close the cabinet.

Choose a control method early. A wall switch gives the cleanest look, while a plug-in timer or smart switch adds scheduling. A dimmer lets you lower the light for evening use. Confirm that the dimmer is rated for LED loads, since standard dimmers can cause flicker.

Control Glare and Color Temperature

Exposed LEDs can create glare when you stand at the sink. Use diffusers or frosted covers, and mount the fixtures toward the front of the cabinet so the light falls onto the counter rather than into your eyes. For most kitchens, a color temperature around 3000K gives a warm, comfortable tone, while 4000K reads cleaner for detailed prep work. Check the fixture specifications before you buy so the tone matches the rest of your lighting.

Common Mistakes and Tips

  • Skipping the voltage check before closing up the cabinets, which makes later fixes harder.
  • Undersizing the power supply, which can cause dim or flickering lights across a long run.
  • Mounting fixtures too far back, which leaves the front of the counter in shadow.
  • Running low-voltage cable through a hot zone near the range or dishwasher.
  • Ignoring the manufacturer’s maximum run length, which affects brightness at the far end.
  • Frosted LED channel diffusers help soften the light and hide individual LEDs, which reduces glare at eye level. View on Amazon
  • Plug-in dimmers for LED strips give you control over brightness without rewiring the switch. View on Amazon
  • A non-contact voltage tester lets you confirm the circuit is dead before you work inside the cabinet. View on Amazon

FAQ

Can I install under-cabinet lighting myself?

Plug-in and battery-powered fixtures are a straightforward DIY project. Hardwired installs that tie into the household circuit should be handled by a licensed electrician.

How far apart should the lights be spaced?

Many fixtures work well at 6 to 12 inches apart, but follow the spacing in the manufacturer’s instructions for your specific product.

Why are my LED lights flickering after I installed a dimmer?

The dimmer is often not rated for LED loads. Replace it with a model labeled for LED use and confirm the driver is compatible.

Conclusion

Good under-cabinet lighting comes from careful planning: spacing the fixtures, hiding the wiring and controlling glare. Take the time to test connections before closing up the cabinets. Check local code and consult a licensed electrician for any hardwired work.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our kitchen design & remodeling guides, checking product details against manufacturer specifications and owner feedback.