Updated November 2026
A red brick backsplash in kitchen spaces gives you warm texture, a strong focal point and a finish that feels built rather than applied. This guide walks through how to plan the layout, choose between real brick and brick-look options, and avoid the mistakes that make brick look dated or hard to clean. By the end, you will have the measurements and decisions you need to start a kitchen with red brick backsplash.
Decide Between Real Brick and Brick-Look Materials
Real clay brick is the most authentic route. Thin brick veneer, sold as slips about 1/2 inch thick, is the usual choice for backsplashes because it avoids the weight and depth of full bricks. Brick-look options, such as porcelain or ceramic tile printed to resemble brick, are easier to clean and more consistent in color. Manufacturers of brick veneer typically specify that it should be installed over a cement backer board and set in a flexible mortar, so check the product sheet before you buy.
Shopping for one? See our guide: 6 Best Bricks for Kitchen Backsplash Options in 2026.
Plan the Layout and Measurements
Red brick is a busy pattern, so the layout matters more here than with plain tile. Measure the wall from counter to upper cabinet bottom, usually 18 inches, and from corner to corner in each run. Standard running bond, where each row is offset by half a brick, is the most common layout. Stack bond, with vertical joints lined up, looks more modern but shows every small misalignment.
- Measure height and width of each wall section, including outlets and the range hood.
- Dry-lay a row of brick on the floor to see how the cuts land at corners.
- Plan so that cut pieces fall at the ends of rows, not beside the range.
- Mark a level reference line before setting the first course.
Prepare the Wall and Set the Brick
Start with a clean, flat, dry surface. Apply cement backer board or a similar substrate where the wall is uneven, then set the brick with a thin-set or mortar rated for veneer. Work from the bottom course up, check level frequently, and keep joints a consistent width, typically about 3/8 inch for a classic look. Clean any mortar smears before they dry, because red brick absorbs grout haze quickly.
Grout, Seal and Protect the Surface
Use a grout suited to the joint width and a sealer designed for brick. Sealing matters because brick is porous and grease from cooking can darken it. Apply sealer after the mortar has fully cured, following the manufacturer’s stated cure time, and reapply as the product directs. For wiring, outlets and gas or electric range work, consult a licensed electrician or contractor before cutting into the wall.
Common Mistakes
- Skipping a sealer, which lets grease darken the brick over time.
- Using full-depth brick where the counter and outlet boxes cannot accommodate it.
- Choosing a bright, saturated red with no lighter elements, which can feel heavy in small kitchens.
- Ignoring the range area; heat and splatter demand a sealed, cleanable finish.
- Forgetting to plan lighting, since textured brick casts shadows under upper cabinets.
Red Brick Backsplash Tips for Balance
Pair the brick with light cabinets, white or pale stone counters, or matte black hardware to keep the wall from overwhelming the room. If you are still comparing textures, the guide to White Brick Kitchen Backsplash: A Step-by-Step Guide to Planning One shows how a lighter brick changes the mood, and 6 Best Bricks for Kitchen Backsplash Options in 2026 covers the main brick types side by side. For a contrasting finish, Subway Tile as Backsplash in Kitchen: A Step-by-Step Layout Guide is useful when you want a cleaner line.
Recommended gear
- Notched trowel and tile spacers help keep veneer courses level and joints consistent. View on Amazon
- Brick and stone sealer protects porous veneer from grease and staining. View on Amazon
- Cement backer board gives veneer a stable, moisture-resistant base. View on Amazon
FAQ
Is a red brick backsplash hard to clean?
Sealed brick wipes clean with mild soap and water, but unsealed brick absorbs grease. Reapply sealer on the schedule the product manufacturer specifies.
Can I install brick veneer myself?
Many homeowners with basic tiling experience can do it, but cutting for outlets and working near gas or electric lines calls for a professional. Confirm your local requirements first.
Does red brick suit a small kitchen?
It can, if you balance it with light cabinets and a pale counter. Keep the brick to the backsplash zone rather than the full wall to avoid visual crowding.
Conclusion
A red brick backsplash in kitchen design works best when the material, layout and sealing are decided before the first course goes up. Measure carefully, choose between real veneer and brick-look tile, and balance the warmth of the brick with lighter surfaces. Check the manufacturer’s instructions for every product you use.
Related reading
- White Brick Kitchen Backsplash: A Step-by-Step Guide to Planning One
- Wood Backsplash in Kitchen: A Step-by-Step Guide to Choosing and Installing One
- White Marble Backsplash Kitchen: A Practical Guide (2026)
- Wallpaper as a Kitchen Backsplash: A Step-by-Step Guide for Beginners
- Top 6 Kitchen Tempered Glass Backsplash Options for Behind the Stove
- Top 5 Metal Backsplash in Kitchen Options for Modern and Industrial Spaces
