Updated November 2026

To replace countertops in kitchen, you will measure the existing run, choose a material that suits your use and maintenance tolerance, remove the old top safely, and set the new one level and sealed. The process is manageable for a confident DIYer on simple layouts, but sink, cooktop, and gas connections often call for a licensed plumber or installer. Work in the order below and you will avoid the most common expensive mistakes.

Measure and Plan the Replacement

Start by measuring each run in three places: front edge, back against the wall, and midpoint. Walls are rarely square, so the smallest number is your template length. Note the overhang you want, typically 1 to 1.5 inches past the cabinet face, and the depth of your sink cutout. If you are switching materials, check the new slab’s thickness, since a thicker top may affect door clearance or the height of your backsplash. For a deeper look at sizing, see How Much to Replace Kitchen Countertops: Measuring, Scoping and Sizing Your Job.

Shopping for one? See our guide: 7 Best How Much Does It Costs to Replace Kitchen Countertops (2026): Our Picks.

Choose the Right Material for the Job

Match the material to how you cook and clean. Quartz resists stains and needs no sealing. Granite handles heat well but needs periodic sealing. Laminate is light and forgiving to cut but scratches and can delaminate at seams. Butcher block suits prep areas but requires oiling. For a side-by-side comparison, read Types of Kitchen Countertops: Materials, Costs and Care Compared.

Remove the Old Countertop Safely

Prepare the workspace

  1. Shut off the water supply to the sink and disconnect the supply lines.
  2. Disconnect the garbage disposal, dishwasher drain, and any gas line to a cooktop. Cap gas lines only with a qualified professional.
  3. Clear the cabinets and protect floors with drop cloths.
  4. Remove caulk along the backsplash and under the sink flange with a utility knife.

Lift the top free

Unscrew the mounting brackets from inside the base cabinets. Most tops are attached with corner blocks or clips driven into the cabinet frame. Loosen any silicone adhesive gently with a plastic putty knife. Lift from the back edge with two people; stone tops are heavy and brittle.

Install the New Countertop

Dry-fit the new slab before applying adhesive. Check that the cutouts align with the sink and cooktop locations, then set the top with a silicone or construction adhesive bead along the cabinet frame. Shim the cabinets so the top sits level within about 1/8 inch across the run, and secure it through the corner brackets. Set the sink, reconnect plumbing, and seal the seam between the top and backsplash.

Finish and Seal

Allow the adhesive to cure as the manufacturer specifies before loading the surface. Seal natural stone according to the product label, typically after installation and then on a recurring schedule. Apply a bead of color-matched caulk along the wall line to keep water out of the joint.

  • A digital level helps you confirm the top is flat before the adhesive sets, since small tilts show up quickly under a sink. View on Amazon
  • A set of plastic shims lets you adjust cabinet height in small increments without splitting wood. View on Amazon
  • Silicone caulk formulated for countertop seams resists moisture and mold better than general-purpose products. View on Amazon

Common Mistakes

  • Measuring once. Always confirm dimensions after cabinets are fully secured and the old top is removed.
  • Skipping the dry fit. A top that will not seat means cutting or reordering material.
  • Ignoring the backsplash. Taller or thicker tops can change how the wall joint looks and seals.
  • Overtightening brackets. Compressing the cabinet can pull doors out of alignment.
  • Rushing the cure time. Loading the top early can shift the setting and crack the seam.

FAQ

How long does it take to replace countertops in kitchen?

Removal and installation of a simple run often takes one to two days of active work. Templating and fabrication for stone usually happens separately and adds time before install day.

Can I replace countertops without removing cabinets?

Yes, in most cases. The new top sits on the existing base cabinets, provided they are level, structurally sound, and the top’s thickness works with your door clearance.

Do I need a professional to replace countertops?

Laminate and butcher block are reasonable DIY projects for many homeowners. Stone tops, sink plumbing, and gas connections should be handled by a licensed professional to protect warranties and avoid safety risks.

Conclusion

To replace countertops in kitchen well, measure carefully, choose a material that fits your habits, and work through removal and installation in order. Take time with leveling and sealing, since those details decide how the surface performs for years. When plumbing or gas is involved, bring in a licensed professional.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our kitchen design & remodeling guides, checking product details against manufacturer specifications and owner feedback.