Updated November 2026
Under cabinet kitchen lighting installation is a manageable weekend project when you plan the layout first. In this guide you will map your fixtures, choose a power route, mount the lights and wire them to a switch, so your countertops get even, glare-free task light. Most homeowners can handle the mounting and low-voltage work, but check local electrical codes and consult a licensed electrician before touching any line-voltage wiring.
Plan the Layout and Choose Your Fixtures
Start by measuring the run of counter you want to light. Count only the continuous stretch of base cabinets, and note where the range hood, sink and any open shelving interrupt the line. Lights mounted at the front edge of the cabinet bottom, about 2 inches back from the front, usually throw the best light across the work surface.
Shopping for one? See our guide: 7 Best Kitchens Under Cabinet Organizer Picks Compared (2026).
Fixture spacing depends on the product. Many LED puck and strip systems are designed to be spaced roughly 12 to 24 inches apart, so check the manufacturer’s spacing chart before you buy. For a quick comparison of fixture types, see Best Under-Cabinet Lighting for Kitchens: 6 Fixtures Compared. If you are still settling the lighting plan for the whole room, Under-Cabinet Lighting: Planning Counter Light walks through how task light fits with ceiling and pendant lighting.
Gather Tools and Mark the Mounting Line
Most installs need only basic hand tools. Before you start, shut off the circuit at the breaker and confirm it is dead with a voltage tester.
- Drill with bits suited to your cabinet material
- Level and tape measure
- Pencil and painter’s tape for marking
- Wire strippers, connectors and a voltage tester
- Screwdriver set and mounting clips or adhesive tape, as the fixture requires
- Fish tape if you need to route wire through a cabinet or wall
Mark a straight reference line along the underside of each cabinet with the level. Lay out fixture positions and tape them down so you can see the spacing before anything is drilled.
Mount the Fixtures and Route the Wiring
Install the Lights
Clean the underside of the cabinet so the adhesive or mounting clips grip well. Attach the mounting channels or clips along your reference line, then snap or screw in the fixtures. Keep the connector ends accessible so you can reach them later. Leave a small service loop of wire at each junction so you can make repairs without tearing out the work.
Run the Power Feed
Most under-cabinet systems use a low-voltage driver or transformer. Mount the driver inside a cabinet, away from the sink and heat sources, and leave room for airflow. Route the low-voltage cable along the back of the cabinets and through drilled holes, keeping it clear of moving drawers and hinges. Line-voltage connections to the house circuit must be made in a junction box and should be handled by a licensed electrician.
Wire the Switch and Test Every Light
Connect the driver output to the fixtures according to the manufacturer’s diagram, then power the system and test each light before closing anything up. Check for flicker, dim spots and uneven brightness at the counter line. A wall switch or under-cabinet toggle is the simplest control, while a dimmer adds flexibility if the driver is compatible with it.
| Check | What to look for |
|---|---|
| Brightness | Even light across the full counter length |
| Color | Same color temperature on every fixture |
| Glare | No bright hot spots visible from standing height |
| Heat | Driver stays cool to the touch after an hour |
Common Mistakes and Tips
- Mounting fixtures too far toward the back, which leaves the front edge of the counter in shadow.
- Mixing color temperatures across fixtures, which makes the counter look patchy.
- Skipping the service loop, which makes future repairs much harder.
- Placing the driver where it has no airflow or sits near the sink.
- Ignoring the manufacturer’s maximum run length, which can cause dim ends.
Recommended Gear
- Voltage tester: confirms the circuit is dead before you touch any wiring. View on Amazon
- Cable clips and wire management kit: keeps low-voltage runs tidy along the cabinet backs. View on Amazon
- Quick-connect wire connectors: make secure, reusable joints at each fixture without soldering. View on Amazon
FAQ
Can I install under cabinet lights myself?
Many homeowners mount fixtures and run low-voltage cable without help. Any connection to the house wiring should be made by a licensed electrician.
How far apart should under cabinet lights be placed?
Spacing depends on the fixture, so follow the manufacturer’s chart. Lights spaced too far apart will leave dark patches on the counter.
Where should the driver be mounted?
Mount it inside a cabinet, out of the way of water and heat, with room for airflow. Keep it reachable so you can service it later.
Conclusion
A careful plan, clean mounting and a tested wiring run will give you even task light across the counter. Take your time with layout and spacing, since that step matters most for the final look. When in doubt about the electrical connections, bring in a licensed electrician.
