Updated November 2026
Kitchen cabinets measurements sizes follow a set of conventions that most manufacturers share, so you can plan a full layout before you order anything. This guide shows you the standard widths, heights and depths, how to measure your room accurately, and how to check that the numbers add up. By the end, you will have a cabinet schedule you can take to a supplier or installer.
Know the Standard Cabinet Sizes
Most stock base cabinets are 24 inches deep, measured from the face of the cabinet to the back wall, and 34.5 inches tall before a countertop is added. Standard wall cabinets are usually 12 inches deep and come in heights such as 30, 36 and 42 inches. Widths are typically sold in 3-inch increments, starting at 9 inches and running up to 36 inches or more for base units.
Shopping for one? See our guide: 4 Best White Oak Kitchen Cabinets (2026): Expert Picks.
For a deeper look at each category, see Standard Kitchen Cabinet Sizes: A Designer's Guide to Widths, Heights and Depths. Keep in mind that these are industry norms, not rules. Custom and semi-custom lines may vary by a fraction of an inch. For a deeper look, Average Coffee Table Measurements: Sizes by Sofa and Room (2026) covers this in detail.
Measure Your Kitchen Step by Step
Good measurements start with the room, not the cabinets. Work with a steel tape and record every number in inches, to the nearest eighth.
- Sketch the room to scale on graph paper, marking doors, windows, outlets, vents and plumbing.
- Measure each wall’s total length at floor level, then again at 36 inches up, since walls are rarely perfectly straight.
- Record ceiling height at several points and note any soffits or bulkheads.
- Measure the depth of the wall between studs where appliances or tall units will sit.
- Check for out-of-square corners by measuring diagonals; a difference of more than about half an inch matters for filler planning.
Plan Widths, Heights and Fillers
Lay out base cabinets first, working from the sink and range positions. Leave a clear landing area of at least 15 inches on each side of the range and sink where possible. Then fill the remaining run with the widest cabinets that fit, using narrower units or filler strips to close gaps.
Wall cabinets are usually hung so the bottom sits 18 inches above the countertop, which places the top near 84 to 86 inches from the floor. If you plan to install under-cabinet lighting, check the clearance first; the guide on Under Cabinet Kitchen Lighting Installation: 7 Steps to a Clean, Even Glow covers how to coordinate lighting with cabinet placement.
Countertop Height and Cabinet Fit
Base cabinets combined with a standard countertop create a finished work surface near 36 inches. Your countertop thickness and any backsplash both affect the final result, so confirm them before you finalize wall cabinet heights. For practical guidance, read What Is the Standard Height of Countertops in Kitchen? Sizes and Fit Tips.
Cabinet Size Reference Table
| Cabinet type | Typical depth | Typical height | Common widths |
|---|---|---|---|
| Base cabinet | 24 in | 34.5 in | 9 to 36 in, by 3 in |
| Wall cabinet | 12 in | 30, 36, 42 in | 9 to 36 in, by 3 in |
| Tall pantry | 24 in | 84 to 96 in | 18, 24, 30, 36 in |
Common Mistakes
- Measuring only once. Re-check every wall before ordering.
- Ignoring appliance specs. Confirm the exact opening width for ranges, dishwashers and refrigerators.
- Forgetting the countertop and backsplash when setting wall cabinet heights.
- Skipping filler allowances, which can leave awkward gaps at corners or walls.
- Assuming all brands share identical dimensions. Always check the manufacturer’s spec sheet.
Recommended gear
- Steel tape measure for accurate wall and opening readings. View on Amazon
- Four-foot level to check that walls and existing cabinets are plumb before you mark layout lines. View on Amazon
- Laser distance measurer for quick checks of long runs and ceiling heights. View on Amazon
FAQ
What is the most common base cabinet depth?
Most standard base cabinets are 24 inches deep, which pairs with a countertop that overhangs the front by about 1 inch. Wall cabinets are usually 12 inches deep.
How much space should I leave between countertop and wall cabinets?
Standard practice is 18 inches of clearance, though many designers adjust this to suit the range hood and the homeowner’s reach. Confirm the number against your appliance and hood requirements.
Do I need a professional to measure my kitchen?
Most homeowners can take accurate measurements with a good tape and a level. For complex layouts, structural changes or electrical and plumbing work, consult a licensed professional before finalizing.
Conclusion
Accurate kitchen cabinets measurements sizes come down to measuring the room carefully, starting from the appliances and sink, and checking every dimension twice. Once you know the standard depths, heights and widths, you can build a cabinet schedule that fits your space. Confirm final figures with your cabinet supplier and installer before ordering.
