Updated November 2026
Canned lighting in kitchen layouts, usually called recessed or can lights, gives you clean ambient light without fixtures hanging into the room. This guide walks through how to plan the layout, space the lights, choose trims and avoid the glare and dark spots that make many kitchens feel flat. The steps apply whether you are adding cans to a new ceiling or retrofitting an existing one.
Step 1: Map Your Work Zones First
Start with a floor plan, not a light count. Mark the sink, cooktop, prep counters, island and any dining area. Each zone needs its own light, and the cans should land on the work surface rather than the ceiling above it. If you are unsure how the layers fit together, the guide to Kitchen Lighting Plan: Task, Ambient and Accent Layers explains how ambient and task light divide the work.
Shopping for one? See our guide: Top 4 Kitchen Lighting Ceiling Lights for Every Layout.
Step 2: Space the Cans Using the Ceiling Grid
A common starting point is to space cans about 2 to 4 feet apart, measured center to center, and to keep them roughly 24 to 30 inches from walls and cabinets. Closer spacing gives more even light but costs more fixtures and wiring. Fewer, wider-spaced cans can create pools of light and dark. Lay out the grid on the ceiling with painter’s tape before you cut anything.
Step 3: Choose Aperture Size and Trim
Most kitchen cans use 4-inch or 6-inch apertures. Four-inch cans suit tighter ceilings and smaller spaces, while 6-inch cans throw more light and are easier to find in a wider selection of trims. Pick a trim that controls glare: a deep baffle or a recessed trim hides the bulb from normal sightlines. Specify a color temperature of about 3000K to 3500K for a warm, flattering light, or 4000K for a crisper, task-oriented look.
Step 4: Plan the Wiring and Switching
Separate task lights from ambient lights on different switches or dimmers so you can run the room at different levels. Check that your recessed fixtures are rated for insulation contact if your attic is insulated over the ceiling. Confirm the circuit load and the housing type before you buy. A licensed electrician should confirm the wiring plan, especially for new circuits.
Step 5: Light the Cabinets and Walls Separately
Canned lights alone often leave upper cabinet faces and wall surfaces dim. Aim a few cans toward the walls or add under-cabinet strips for the counter. Layering this way keeps the room from looking like a single bright disk of light. The guide to Under Cabinet Kitchen Lighting Installation: 7 Steps to a Clean, Even Glow covers the counter layer in detail.
Step 6: Check Color Consistency
Mixing bulbs from different brands is a frequent cause of uneven color. Buy every can and bulb from the same line where possible, and check that the CRI rating is at least 90 for accurate color in food and finishes.
Step 7: Test Before Finishing the Ceiling
Before drywall goes up, run a temporary light or a rough test to check sightlines. Stand at the sink, the range and the island and make sure no bulb sits directly in your eyeline when you stand up.
Checklist for Your Plan
- Floor plan with zones marked
- Ceiling grid laid out with tape
- Aperture size and trim chosen
- Color temperature and CRI confirmed
- Separate switches or dimmers planned
- Insulation contact and load ratings checked
- Electrician review completed
Common Mistakes
- Placing cans directly over the sink or range, where they cast shadows on your hands.
- Using trims with no baffle, which puts the bulb in plain view.
- Mixing color temperatures across fixtures.
- Skipping dimmers, which leaves you with only one brightness level.
- Forgetting that cabinets and walls need their own light.
Recommended Gear
A laser distance measure helps you confirm spacing across a large ceiling in one pass, and a stud finder with AC detection keeps you clear of wiring when you locate housing positions.
A non-contact voltage tester is a basic safety tool for confirming a circuit is dead before you touch any wiring.
FAQ
How far apart should canned lights be in a kitchen?
Many designers start with 2 to 4 feet between centers and 24 to 30 inches from walls. Adjust based on ceiling height and how much light you need at the counters.
What color temperature works best for kitchen cans?
Around 3000K to 3500K gives a warm, comfortable feel, while 4000K is crisper and often used for task areas. Keep all fixtures in the same range.
Should I hire an electrician for recessed lighting?
Yes, for new circuits or ceiling work, a licensed electrician should handle wiring and load checks. Consult a professional before making any electrical changes.
Conclusion
Planning canned lighting in kitchen spaces comes down to zones, spacing, trim choice and layered control. Map the work areas first, then space and specify the cans to match. Test sightlines before the ceiling is closed up, and your kitchen will feel even and comfortable to work in.
