Updated November 2026

Kitchen over cabinet lighting refers to fixtures mounted on top of wall cabinets or along the soffit, aimed down and across the upper portion of the room. Done well, it adds ambient light to the room, softens shadows on tall storage, and gives the kitchen a layered look that overhead ceiling fixtures alone rarely achieve. This guide walks through placement, fixture choice and a simple install sequence.

Decide Where the Light Should Go

Start by deciding what the light needs to do. Most homes have a ceiling fixture that fills the room, so over cabinet lighting usually serves a different role: it lifts the upper walls, adds depth to the room, and makes the countertop area look brighter without adding a task light at eye level. Mark the top of your wall cabinets and the ceiling line on the wall, then note whether the cabinets run to the ceiling or leave a gap. A gap of 12 to 18 inches is common in standard layouts and is the easiest place to hide a fixture.

Shopping for one? See our guide: 4 Best Over Kitchen Table Pendant Lighting for Dining Spaces (2026).

Choose the Right Fixture Type

Over cabinet fixtures fall into three groups: linear LED strips or bars, puck-style lights, and fixtures that wash light upward onto the ceiling. Strip lighting gives the most even result along a long run. Pucks suit short sections or corners. Uplights are the most effective for making a low ceiling feel higher, though they add the least direct light to the workspace. Check that any fixture you buy is rated for the location, since mounting on top of cabinets can expose it to heat from the room above.

Fixture type Best use Main trade-off
LED strip or bar Long, continuous runs Visible seams if not aligned
Puck light Short sections, corners Spotty light if spaced too far
Upward wash Lifting the room, low ceilings Little direct task light

Plan the Wiring and Controls

Decide early whether the lights will be hardwired to a switch, plugged into an outlet, or run on batteries. Hardwired installs need a licensed electrician if you are not comfortable working inside walls, and the circuit should be checked for capacity before you add load. Battery and plug-in options avoid wall work but leave cords or battery swaps to manage. Plan a single switch or dimmer that controls the whole run, so the light is easy to use at every hour.

Install in a Clean Sequence

Once the fixtures and power plan are set, follow this order to keep the work tidy and the light even:

  1. Turn off power at the breaker and confirm with a tester.
  2. Mount the mounting channels or brackets along the top of the cabinets, level and centered.
  3. Run wire through the gap or chase, keeping cable clear of heat sources.
  4. Lay out fixture positions, spacing them evenly, and mark the locations.
  5. Connect the fixtures to the driver or transformer, then secure the driver in an accessible spot.
  6. Test each section before closing the gap, and adjust aim so light falls on the counter and walls, not into eyes.

Common Mistakes

  • Placing lights too far toward the front edge, which creates glare and leaves the back of the counter dim.
  • Mixing LED color temperatures across the run, which makes the light look patchy.
  • Skipping a dimmer, so the light is either too strong at night or too weak for tasks.
  • Ignoring access to the driver, which makes future repairs difficult.
  • Overlooking heat ratings on fixtures mounted in tight spaces.

A simple voltage tester helps confirm the circuit is dead before you touch any wire. View on Amazon

Mounting channel or aluminum profile makes LED strips look neat and dissipate heat. View on Amazon

FAQ

Can I put over cabinet lighting on cabinets that go to the ceiling?

Yes, but you will need a fixture that mounts to the cabinet face or sits in a recessed channel. Uplight fixtures are usually the easiest option when there is no gap above the cabinets.

How many fixtures do I need for a standard kitchen?

It depends on run length and fixture output. Measure the total linear run, then space pucks or strips evenly so the light overlaps slightly at each point.

Should I hire an electrician?

If the install requires new wiring or a new switch inside a wall, consult a licensed electrician. Battery or plug-in options can be handled without that step.

Conclusion

Kitchen over cabinet lighting works best when it is planned around the room’s ceiling height, cabinet layout and control needs. Choose a fixture type that matches the run, install in a clean sequence, and test the light before closing everything up. Careful spacing and a single dimmable circuit will give you even, comfortable light for years.

Colin Foster

About Colin Foster

Colin Foster is part of our editorial team and reviews and edits our kitchen design & remodeling guides, checking product details against manufacturer specifications and owner feedback.